MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 50

Page: 50 / 178

Copyright by Servizio Clienti ANGELO PO Spa

The management program of the oven consists of two parts:

Firmware (FW)

– it controls the operation of the oven (inputs and outputs) – it is in the

power board (2)

Software (SW) - Contains all the user interface, programmes, pictures, etc

… – it is in the

CPU

The following procedure allows:

a) to set the temperature measurement unit (°C or °F)

b) to enable / disable the automatic preheating,

c) to display the SW and FW versions

- With the oven on in standby mode, push for at least 4 seconds the "reset" button, when it

is released the display turns off

a) Press the "temperature" button and turn the knob to change the temperature unit

setting (° C or ° F).

Press the “time” button and turn the knob to set the automatic preheating

c) Hold the "washing" button for at least 3sec to see the SW and FW versions.

d) Press

“cooldown” and turn the knob to enable / disable the cooldown with water

injection during cooking.

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands

MARMON ANGELO PO COMBISTAR FX, Technical Manual

Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands