MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 131

Page: 131 / 178

Copyright by Servizio Clienti ANGELO PO Spa

131

The operation of the circuit is similar to the FM: the oven is running automatically heated

and holding the temperature most suitable for washing and rinsing, while the application of

the chemicals must be done manually by the operator when the display shows the letters

CLE.

The automatic rinsing is made simultaneously by opening the solenoid valves for rinsing

and steam production.

In level 1 the rinsing must be done manually by the operator when H2O shows on the

display. Open the door and spray water with a hose into the chamber.

In case of low pressure or broken solenoid valve the alarm E26 will appear.

The level 2 ovens have 2 cleaning programs:

“

CLE

” “

P01

” and “

CLE

” “

P02

”

selectable with the cleaning button. The cleaning program P02 performs twice the cleaning

program P01.

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

MARMON ANGELO PO COMBISTAR FX, Technical Manual, Page: 131 / 178

Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews: