MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 33

Page: 33 / 178

Copyright by Servizio Clienti ANGELO PO Spa

How to update software and firmware

To update the software and firmware, proceed as follows:

- Enter the service menu

- Insert the key into the USB connector

- Select "Update SW, FW"

- Wait until the end of the procedure and follow the instructions that appear on the

display

- During this procedure,

the message “turn off and on the oven” will appear. This has

to be done by the green power switch. Attention! Don’t remove the USB Stick! (if

you switch from version 1.x to 2.x, the system will require a second reboot, again

without removing the USB stick!)

- Remove the USB stick only when the complete update has been finished (when the

main menu is displayed)

WARNING: In case of power loss during this procedure, both the electronic

boarding could be damaged beyond repair

Update parameters:

This selection starts the procedure for updating parameters of the

boards without the USB stick. It is performed normally

when you change the power

board 2 or the CPU 1a

in order to align the parameters of the boards. To activate the

update, enter the password

FA53

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands

MARMON ANGELO PO COMBISTAR FX, Technical Manual

Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands