MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 40

Page: 40 / 178

Copyright by Servizio Clienti ANGELO PO Spa

3.5.1.

Warning on electric hazard

Once you remove the power supply on the oven, you have to wait 3 minutes before

starting maintenance on the inverter or the motor due to electrical hazards.

3.5.2.

Inverter Alarm Table

E06:3

The inverter bus voltage is lower than

85% of the nominal value

check the inverter voltage (220VAC)

E06:4

the inverter bus voltage has dropped

below the minimum allowable

check the inverter voltage (220VAC)

E06:5

the inverter bus voltage has raised up

to the maximum allowable

check the inverter voltage (220VAC)

E06:6

The inverter is not able to turn the

motor

check that the motor is free to move. Check that

the three phases are connected to the motor.

E06:7

Motor overload

check that the motor is free to move

and doesn’t

touch any other item

E06:8

Excessive heating of the dissipater

verify that the ambient temperature is below

50°C. Verify that the cooling fan inside the

inverter works properly

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands

MARMON ANGELO PO COMBISTAR FX, Technical Manual

Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands