Mackie DL1608 Page 107 Reference Manual Download

Page: 107 / 121

Mackie DL1608 Reference Guide V1.2

107

Appendix D : Hookup Diagrams

Live Sound: House Engineer

Here’s a pretty common setup utilizing the DL1608. Drums are mic’d up and sent to input channels 1-7.

An additional seven mics are connected to input channels 8-14. These may be used to mic guitar and

bass cabinets, acoustic guitar, lead and background vocals, a horn section, etc. A keyboard is connected

to channels 15-16 via 1/4" input jacks.

The L/R main outs of the DL1608 connect directly to a pair of Mackie HD1501 powered subwoofers

which are connected to a pair of Mackie HD1221 powered loudspeakers. Aux sends 1-4 are sent to four

separate SRM450v2 powered loudspeakers set up as monitors for the band. Aux sends 5-6 are sent to

transmitters for in-ear monitors.

The house engineer’s iPad is connected (but not locked) to the DL1608 where he/she will set the LR main

mix, as well as get the 2-track recording of the band’s live show.

Keyboard

Wireless

Router

(Wi-Fi)

Headphones

SRM450v2 Powered Monitors

Drums

Microphones

Transmitters

for in-ear

monitors

Mackie HD1501

powered subwoofer

Mackie HD1221

powered loudspeaker

Mackie HD1221

powered loudspeaker

Mackie HD1501

powered subwoofer

Summary of Contents for DL1608


























































































































Search results

Summary of Contents for DL1608

Reviews:

Related manuals for DL1608

Brands by name

Popular brands

Mackie DL1608, Reference Manual

Search results

Summary of Contents for DL1608

Reviews:

Related manuals for DL1608

Brands by name

Popular brands