Mackie DL1608 Reference Manual Download

Page: 15 / 121

Mackie DL1608 Reference Guide V1.2

PadLock™

Also included with the mixer is a DL1608 PadLock. This is used to lock the iPad into place on the mixer.

One might use this for fixed installs where a dedicated iPad is used and (Pad)locked to the mixer.

Or leave the PadLock off so the iPad may be conveniently transferred in and out of the DL1608.

After docking the iPad (not shown), the PadLock needs to be attached by moving it right

to left [horizontal green arrows],

NOT

downward. This ensures that the foam compresses

against the iPad and holds it solidly in place. Then hand-tighten each of the two security

screws down [vertical green dotted line] using the supplied wrench.

While the PadLock provides some level of security, it is NOT foolproof or guaranteed

protection. LOUD Technologies Inc. is not responsible for the loss, theft, damage or

destruction of your DL1608 mixer or iPad whether a PadLock has been used or not.

Summary of Contents for DL1608


























































































































Search results

Summary of Contents for DL1608

Reviews:

Related manuals for DL1608

Brands by name

Popular brands

Mackie DL1608, Reference Manual

Search results

Summary of Contents for DL1608

Reviews:

Related manuals for DL1608

Brands by name

Popular brands