M-system TR30 User Manual Download Page 9 | Manualshive

Page: 9 / 244

M-system TR30 User Manual Download Page 9

9

TR30-G USERS MANUAL EM-8631-G Rev.16

1.2 Precautions

■

CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument panel of a metal enclosure.
• The actual installation environments such as panel configurations, connected devices and connected wires

may affect the protection level of this unit when it is integrated in a panel system. The user may have to
review the CE requirements in regard to the whole system and employ additional protective measures to
ensure CE conformity.

■

GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power supply for safety.
• The unit does not support hot insertion/removal of modules. When the unit is used in combination with R30

I/O modules, hot insertion/removal of module is not supported for R30 I/O modules.

• Before you remove the terminal block or mount it, turn off input signal for safety.

■

ENVIRONMENT

• Indoor use.
• When heavy dust or metal particles are present in the air, install the unit inside proper housing with sufficient

ventilation.

• Do not install the unit where it is subjected to continuous vibration. Do not subject the unit to physical im-

pact.

• Environmental temperature must be within 0 to 50°C (32 to 122°F) with relative humidity within 10 to 90% RH

in order to ensure adequate life span and operation.

■

WIRING

• Do not install cables close to noise sources (relay drive cable, high frequency line, etc.).
• Do not bind these cables together with those in which noises are present. Do not install them in the same

duct.

• Max. wiring length for FE terminal should be 3 meters.
• Be sure to attach the terminal cover for safety.

■

ABOUT SD CARDS

• Do not turn off the power of the unit during writing data. Insert or eject SD card according to the specified

procedure.

• Confirm the front and back side of the SD card.

■

CALENDAR CLOCK

• A backup battery is employed for calendar clock IC. Backup period without power supply is approx. 2 years.
• With power on, the battery is not drained. When total power off period is approx. 2 years, the battery cannot

backup the calendar clock. The calendar clock cannot keep correct date and time.

• The battery is not replaceable by customer. When replacement is required, consult M-System.

■

AND ....

• The unit is designed to function as soon as power is supplied, however, a warm up for 10 minutes is required

for satisfying complete performance described in the data sheet.

■

LOGIN ID & PASSWORD

• The Login ID and password of the device are simple functions. They do not guarantee complete security.
• We recommend the user to apply own ID/password setting and not to leave the setting unused or at default

values.

«
...
7
8
9
10
11
...
»

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands