manualshive.com logo in svg

M-system TR30, User Manual

Share
Download
M-system TR30 User Manual Download Page 207

207

TR30-G   USERS MANUAL  EM-8631-G  Rev.16

7.  Appendix

7.1  Primary method of operation of the touch panel

The primary method of operation of the touch panel used in this User Manual is explained below.

 

■

Tap

 

Lightly tap any point on the screen with your finger and immediately remove your finger. (a light rap)
Use to select an item such as an icon or menu.  Equivalent to the click operation in relation to the mouse. 

 

■

Pinch in

 

Touch the screen with 2 fingers, and close the gap between the fingers.  Use to shrink the display.

 

■

Pinch out

 

Touch the screen with 2 fingers, and increase the gap between the fingers.  Use to enlarge the display.

 

■

Flick

 

Touch a point or specific position on the screen, and move your finger without taking it off from the screen.
Similar to the drag and drop operation in relation to the mouse.

 

■

Swipe

 

Rather than touching a particular point as when flicking, move (slide) a wide area of the screen.
Similar to the wheel scroll operation in relation to the mouse.

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands