manualshive.com logo in svg

M-system TR30, User Manual

Share
Download
M-system TR30 User Manual Download Page 47

47

TR30-G   USERS MANUAL  EM-8631-G  Rev.16

(2)  Set various parameters by referring to the table below.

Parameter

Description

Partitions

Set the number of partitions to be used. You can select from: Not to be used / 2 / 3 / 4 / 5.

Name

Set a name which is less than 32 characters for each zone.

Color

Set a color to represent each zone which will be displayed on the Web screen.

Upper limit
       :
       :
       :
Lower limit

Set the upper and lower limit value for these zones as actual values.  Set the upper limit value 
> lower limit value.
• When the deadband is set
When a deadband is set between zone 1 and zone 2, please set the values so that the 
deadband is between the upper limit value for zone 1 and the lower limit value for zone 2.  Set 
similarly for the other zones as well.
• When the deadband is not set
When the deadband is not set between zone 1 and zone 2, please set the same value for the 
upper limit value of zone 1 and the lower limit value of zone 2.  Set similarly for the other zones 
as well.

Trigger recording

Set whether or not to record when there is a change in the input value and it enters a certain 
zone.
You can select from: Disable / Start / Stop.

New memory block

Set whether or not to run a start new memory block when there is a change in the input value 
and it enters a certain zone.
You can select from: Disable / Enable.

CAUTION

If the new memory block lasts for a short time, data on a memory block which has not been 
transferred to the SD card may get overwritten.  Set the start new memory block interval as a 
multiple of 10 seconds.

Color

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands