manualshive.com logo in svg

M-system TR30, User Manual

Share
Download
M-system TR30 User Manual Download Page 73

73

TR30-G   USERS MANUAL  EM-8631-G  Rev.16

(3)  Set the [CH setting] as [SLMP], and enter the parameters in the table below.

1. Select

2. Enter

3. Enter

Parameter

Description

Slave No.

Enter the slave No. (0 to 11) set in (1).

SLMP device

Choose the device code of the SLMP device to be connected.

SLMP device No.

Set the device No. of the SLMP device to be connected.
When the slave type of the selected Slave No. is [SLMP 16bit], set the device 
No. of the smaller number because the PI data is 32 bit data set in two ad-
dresses. 
Check or uncheck the [Invert] check box depending on the order of high/low 
devices.

Measuring mode
(Modbus/TCP·SLMP)

Set the type of the 32 bit data read from the remote I/O.   
Select from the following.
• Accumulation
The cumulative total is calculated by accumulating the difference between the 
value at the start of cumulative totalizing and the value when it is reset, for each 
sampling duration.  This corresponds to the cumulative total data of the SLMP 
device.
• Actual value
The retrieved data is recognized as a signed 32 bit integer, and its value is taken 
as sampling data.  This corresponds to the power data of the SLMP device.
• Float
The retrieved data is recognized as single precision floating point, and its value 
is taken as sampling data.  This corresponds to the power data of the SLMP 
device.

Pulse range

Set the same value as the pulse range set in the SLMP device.   
For details, please see the User Manual for the SLMP device which you are us-
ing.

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands