manualshive.com logo in svg

M-system TR30, User Manual

Share
Download
M-system TR30 User Manual Download Page 48

48

TR30-G   USERS MANUAL  EM-8631-G  Rev.16

Upward setting / Downward setting (AI)

This event occurs when the zone which has been set in the zone setting is changed.

(1)  Click on the [Alarm zone setting] button in the [AI setting] to display the [Alarm zone setting].
 

Click on the tab [Upward] or [Downward].

(2)  Set various parameters by referring to the table below.  Once the setup is complete, press the [OK] button 

and temporarily store the setting.

Parameter

Description

Event log

Set whether or not to record an event when there is a change in the input value and it enters a 
certain zone.  To record, put a check in the check box.

Acknowledge

Set whether the event summary/new event needs to be acknowledged or not.

Register new event

Set whether or not to display the input value in the new event screen when there is a change in 
the input value and it enters a certain zone.  To display, put a check in the check box.

Event No.

Set the event number.
This number can be used to set a filter in the event summary in the Web screen.
(Setting range: 1 to 32)

Message

Set a message which is less than 32 characters to be displayed when an event occurs.

E-mail

Set the mail to be sent when an event occurs.

AI setting

AI alarm zone setting

Click

Basic setting

Upward transition setting

Downward transition setting

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands