manualshive.com logo in svg

M-system TR30, User Manual

Share
Download
M-system TR30 User Manual Download Page 231

231

TR30-G   USERS MANUAL  EM-8631-G  Rev.16

Data range

When the TR30-G device is used as a Modbus/TCP slave, the range of data returned from the slave to the 
Modbus master and data written by the master is as shown in the table below.

Item

Description

AI

•  When the data type is [%] (0 to 10000; voltage/current data of R30 I/O modules or remote I/O 

devices): 
-2000 to 12000

•  When the data type is [Int] (signed integer): 

Signed 16 bit integer (-32768 to 32767)

•  When the data type is [Uint]: 

Unsigned 16 bit integer (0 to 65535) 

PI

•  When the data type is [Accumulation] in Measurement mode: 

Unsigned 32 bit integer

•  When the data type is [Actual value] in Measurement mode: 

Signed 32 bit integer

•  When the data type is [Float] in Measurement mode: 

 32 bit single precision floating point

OI

32 bit single precision floating point

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands