manualshive.com logo in svg

M-system TR30, User Manual

Share
Download
M-system TR30 User Manual Download Page 67

67

TR30-G   USERS MANUAL  EM-8631-G  Rev.16

Alarm output (DI)

A specific DO can be turned ON for each status.

(1)  Click on the [Alarm output] button in the [DI setting] to display the [Alarm output].  Double-click on the DO 

channel to be operated and set as ON/OFF.

(2)  Once the setup is complete, press the [OK] button and temporarily store the setting.

CAUTION

•  Before configuring these setting, please configure the DO setting.

➔

 3.8.7 Discrete output (DO)

•  When DO is turned ON for the alarm output, the ON output continues as long as the alarm 

output status is ON.

•  If the alarm output is not used, please set it as OFF.

Reset totalized value (DI)

The totalized value of a specific PI can be reset in the rising edge of the DI.
Specify this in the [Reset totalized value entry] in the PI basic setting. 

➔

 3.8.5 Pulse input (PI)

Reset function value (DI)

The operation of a specific OI can be reset by switching the DI from OFF to ON.
Specify this in the [Reset function value entry] in the OI basic setting. 

➔

 3.8.6 Function input (OI)

Set each CH by following the above procedure.
The CH setting for which the setting is complete in the [Discrete input (DI)] screen can also be copied to other 
CHs and only the required portions can be edited.

➔

 3.8.8 Copying the CH setting

DI setting

Alarm output

1. Click

2. Double-click

3. Select

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands