Home
/
M-system
/
TR30
/
User Manual

M-system TR30, User Manual

Share

Page: 35 / 244

M-system TR30 User Manual Download Page 35

35

TR30-G USERS MANUAL EM-8631-G Rev.16

3.8.2 Communication Setting

(1) In the [Input/Output] screen, click on the [I/O slave setting] button.
(2) Click on the [Communication] to display the Communication setting.

Input/Output

I/O slave setting

1. Click

Communication setting

2. Click

3. Enter

• Pause period

Considering the communication pertaining to all the registered slaves and all the channels as one batch, set
the time from one communication batch to the next.
This is roughly the same value as the sampling interval.

• Modbus/TCP Timeout

Please set the wait time for a response after a query has been sent.

• Modbus/TCP Transaction ID management

Unintended messages are skipped by the management of Modbus message IDs.

• SLMP Timeout

Please set the wait time for a response after a query has been sent.

Communication

Communication

Slave 0

Pause period

Communication

Communication

Slave 1

Pause period

«
...
33
34
35
36
37
...
»

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands