manualshive.com logo in svg

M-system TR30, User Manual

Share
Download
M-system TR30 User Manual Download Page 116

116

TR30-G   USERS MANUAL  EM-8631-G  Rev.16

(6)  Click on the [Record] button.  The [Record] screen is displayed.

Please set the following parameters.

Storing rate

Set the storing rate.
You can select from: 5 ms / 10 ms / 50 ms / 100 ms / 500 ms / 1 seconds / 2 seconds / 5 seconds / 10 seconds 
/ 1 minute / 2 minutes / 5 minutes / 10 minutes / 15 minutes / 30 minutes /1 hour.

Auto start

Set as [Enable] to start recording automatically once the power supply to the device is turned ON.

Auto file delete

Specify whether to automatically delete files/folders when the remaining space in the SD card reaches 100 MB. 
Set as [Enable] to automatically delete.
But, if you change the folder name in the internal registers in [3.11.4 Modbus/TCP slave], it will not be consid-
ered for auto file delete.

SD card file format

Select the format in which to store files in the SD card of the unit from the 3 types shown in the table below.

SD card file format

Description

TRD

Stored in the binary format.  Can be displayed in the historical trend screen and in TRViewer.
In TRViewer, it can also be converted to the CSV format.

CSV (S-JIS)

Stored in the CSV format using S-JIS character codes.  Cannot be displayed in the historical 
trend screen or in TRViewer.

CSV (UTF-8)

Stored in the CSV format using UTF-8 character codes.  Cannot be displayed in the historical 
trend screen or in TRViewer.

Configuration

Record

1. Click

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands