background image

 

TEO-540-C1A Engine Maintenance Manual

 

72-05

 

© 2018 Avco Corporation. All Rights Reserved 

Page 108 

November 2018 

TEO-540-C1A Engine Maintenance Manual

 

Table 1 (Cont.) 

Sequence of Engine Disassembly Procedures 

Step 

Reference 

 

Step 

Reference 

Step 5 

“Alternator Belt Removal” and 
“Alternator and Bracket Removal” 
procedures in Chapter 72-70 

 

Figure 5 

Alternator Bracket, Alternator, and 

Alternator Belt 

 

Step 8 

Remove the 
fuel hoses, 
throttle 
body, fuel 
injector rail 
assemblies, 
and fuel 
pump 
(Figure 8).

 

Procedures in Chapters 73-10 and 73-20 

 

Fuel Hose Removal 

 

Throttle Body Removal 

 

Fuel Injector Rail Assembly Removal 

 

Fuel Pump Removal 

 

Figure 8 

Fuel System Components 

Remove the 
alternator 
belt, 
alternator, 
and 
alternator 
bracket 
(Figure 5).

 

 

Step 6 

Remove the 
starter 
(Figure 6).

 

“Starter Removal” procedure in 
Chapter 72-70 

 

Figure 6 

Starter

 

 

Step 9 

Remove the 
intake pipes 
(Figure 9). 

“Intake Pipe Removal” procedure in 
Chapter 72-80

 

 

 

Figure 9 

Intake Pipes 

Step 7 

Remove the 
starter ring 
gear support 
(Figure 7).

 

“Starter Ring Gear Support Removal” 
procedures in Chapter 72-70 

 

Figure 7 

Starter Ring Gear Support 

 

Step 10 

Remove the 
oil sump 
(Figure 10). 

 

“Oil Sump Removal” procedure in 
Chapter 72-50

 

 

Figure 10 
Oil Sump 

Summary of Contents for TEO-540-C1A

























































































































































































































































































































































































































































































































































































Reviews: