Australian owned
Australian designed
61 (0)3 9876 0400
[email protected]
www.motolux.com.au
Ordering Information
Australia / New Zealand
Should you need to reset a motor back to Factory Settings you will need to push the button inside the hole in the Head of the
Motor Five Times in quick succession
holding
the button in on the Fifth Push, you will get a Double Jiggle indicating the
motor has been reset and all Limits and Pairing have been deleted.
Example: Putting 5 blinds all on Channel Six.
1.
Start by selecting the channel that you want to pair the motor with on the remote control.
2.
Insert Paper Clip in Hole of Motor for approx. 1 second and the motor will give a jiggle, then on the Remote push the
Up
Button.
3.
The motor will jiggle to indicate that it is paired.
1.
If the direction is correct there is no action required move to
Limit Setting
. If the direction is wrong, Push and
hold
the Stop
Button until you get a Jiggle from the motor then push the Down Button.
2.
Test the blind and the direction should be correct.
1.
Push and
hold
the button in the Setting Hole on the remote with a Paper Clip until you get a jiggle – now move the blind to
where you would like the Top Limit to be – now push and hold the button in the Setting Hole on the remote, you will get a jiggle.
2.
Move the blind to where you would like the Bottom Limit to be – now push and
hold
the button in the Setting Hole on the
remote, you will get a jiggle.
3.
Very Important:
Push and
hold
the button in the Setting Hole on the remote, you will get a jiggle. This has now recorded the
limits, please test the blind.
The above will need to be done for Each Different Motor on Each Different Channel.
1.
On the Remote go to Blind 1 on Channel 1 – Push and
Hold
the Stop Button until you get a jiggle. Now go to Channel 6 and
push and
hold
the Up Button you will get a Jiggle. Blind 1 is now added to Channel 6.
2.
On the Remote go to Blind 2 on Channel 2 – Push and
Hold
the Stop Button until you get a jiggle. Now go to Channel 6 and
push and
hold
the Up Button you will get a jiggle. Blind 2 is now added to Channel 6.
Repeat these steps until you have moved all blinds over to channel 6.
This feature can also be used to transfer motors onto other Remote Controls.
Pairing the Motor to the Remote
Check/Set the Direction
Resetting a Motor Back to Factory
To Add Multiple Blinds to a Group Channel
Limit Setting: TOP LIMIT FIRST
PROGRAMMING INSTRUCTIONS 1/2
Firstly you will need something small enough to put in the both the hole in the head of the motor and in the setting hole on
the remote control, a Paper Clip or Jewelers Screwdriver is perfect.
Install the blind and fit the Battery Wand Clips in the desired position making sure the position is not too far from the motor
with enough for both cables to plug together. Install 8x AA Batteries into the Battery Wand and plug the male and female
plug ends together and clip the wand into position, you should hear a beep indicating the motor has powered on. If no Beep is
heard: Find the hole in the head of the motor and insert a paper clip and give the button inside a quick push, you should get a
Beep indicating the motor is now powered on.
25MM DC EXTERNAL BATTERY 1.2NM MOTOR - 802322012 (MT25-1.2-28-12DE)
Motolux is a world-class manufacturer of motorisation products and systems dedicated to window covering markets
worldwide. A designer and manufacturer of a fully integrated range of motorisation solutions, Motolux products are
suitable for commercial or residential use. Our high quality product range is streamlined to simplify the process of
manufacturing, installation and ongoing maintenance of almost any type of motorised window covering product.
REVISION 2 - 2020
