LNC Robot Series Operation And Program Manual Download

Page: 20 / 95

Joint Robot Manipulator - Software Operation Manual

Advantech LNC Technology Co., Ltd.

4.2.

Various coordinates and their relevance

The system can adapt to a variety of robot types at the same time and uses the same coordinate

concept for development, please be clear, which is helpful for subsequent operations,

programming and development. Some special terms are as follows:

Motor coordinates:

The actual coordinate value of the motor is independent of the coaction

between the mechanisms.

Joint coordinates:

The coordinate value of the motor coordinate after the mechanism coupling

relationship is converted. (visual mechanism state in appearance)

World coordinates:

The position and attitude of Ptool when the center of the manipulator base

is the origin.

Forward kinematics:

An algorithm that converts motor coordinates to world coordinates.

Inverse kinematics:

An algorithm that converts world coordinates to motor coordinates.

Work coordinates:

Converted from world

coordinates (points) through

the work coordinate system

Tool coordinates:

Converted by world

coordinates (points) through

tool coordinates

Joint coordinates

Motor coordinate

Mechanism coupling

Mechanism type and size

World coordinates (points)

Forward kinematics

Inverse kinematics

Tool coordinate system

Reset when (span) pressed

World coordinates (points)

Work coordinate system

Work coordinates

Tool coordinates

(the value of span)

Summary of Contents for Robot Series
































































































Search results

Summary of Contents for Robot Series

Reviews:

Related manuals for Robot Series

Brands by name

Popular brands

LNC Robot Series, Operation And Program Manual

Search results

Summary of Contents for Robot Series

Reviews:

Related manuals for Robot Series

Brands by name

Popular brands