LNC Robot Series Operation And Program Manual Download

Page: 86 / 95

Joint Robot Manipulator - Software Operation Manual

Advantech LNC Technology Co., Ltd.

second set of auto off, after 100ms, the background

program will automatically turn it off).

G22 O205 S7P100

Set O205 to on, the program continues to run (using the

third set of auto off, after 100ms, the background program

will automatically turn it off).

G22 O205 S8 P100

Set O205 to on, the program continues to run (using the

fourth set of auto off, after 100ms, the background program

will automatically turn it off).

17.19.

Set R(G23)

Code description

R: the number of R

T: Numerical type (0 absolute, 1 relative, 2 number, 3 cycles plus 1)

S: Output point status

P: Waiting time , ms

Examples

G23 R2010 T0 V3 P200

Set R2010 to 3, then pause for 200ms.

G23 R2011 T1 V2

R2011 = R2011+2

G23 R2012 T2 V2060

R2012 = R2060

G23 R2013 T3 V10

R2013 = R2013+1, if R2013>10, then set R2013=0

17.20.

Sensing point I stop (Rbit comparison) (G31)

Code description

R: the number of R

S: The value of the R number to be used for the shielding value of the And operation. For

example, when only the bit 0 of the R value is monitored, S1 is used. When only the bit 1 of the

R value is used, S2 is used. When bit 0 and bit 1 are simultaneously monitored, S3 is used.

T: The value after the And operation must be the same as the value of this code to trigger the

action to stop.

L: 0 world, 1 work, 2 tool, 3 joint. (default: work)

M: 0 absolute, 1 relative. (Default: Absolute)

X: Coordinate X or J1.

Y: Coordinate Y or J2

。

Z: Coordinate Z or J3

。

Summary of Contents for Robot Series
































































































Search results

Summary of Contents for Robot Series

Reviews:

Related manuals for Robot Series

Brands by name

Popular brands

LNC Robot Series, Operation And Program Manual

Search results

Summary of Contents for Robot Series

Reviews:

Related manuals for Robot Series

Brands by name

Popular brands