Lenovo System x3250 M5 Installation And Service Manual Download Page 707

Page: 707 / 740

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-816-001 : IMM I2C Test Aborted

Command illegal for specified sensor or record type.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-817-001 : IMM I2C Test Aborted

Command response could not be provided.

Recoverable

Severity

Warning

Serviceable

Yes

Appendix C. DSA diagnostic test results

693

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands

Lenovo System x3250 M5, Installation And Service Manual

Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands