Lenovo System x3250 M5 Installation And Service Manual Download Page 358

Page: 358 / 740

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0122

User Response

Information only; no action is required.

•

4000007b-00000000 : Dynamic Power Savings mode has been turned on by user [arg1].

Dynamic Power Savings mode turned on by user

May also be shown as 4000007b00000000 or 0x4000007b00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0123

User Response

Information only; no action is required.

•

4000007c-00000000 : Dynamic Power Savings mode has been turned off by user [arg1].

Dynamic Power Savings mode turned off by user

May also be shown as 4000007c00000000 or 0x4000007c00000000

Severity

Info

Serviceable

344

Lenovo System x3250 M5Installation and Service Guide

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands

Lenovo System x3250 M5, Installation And Service Manual

Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands