manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

Share
Download
Lenovo System x3250 M5 Installation And Service Manual Download Page 188

If you are instructed to return the server component or optional device, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing a hot-swap hard disk drive

Use this information to replace a hot-swap hard disk drive.

The following notes describe the type of hard disk drives that the server supports and other information
that you must consider when you install a hard disk drive. For a list of supported hard disk drives, see
http://www.lenovo.com/us/en/serverproven/.

• Locate the documentation that comes with the hard disk drive and follow those instructions in addition to

the instructions in this chapter.

• Make sure that you have all the cables and other equipment that are specified in the documentation that

comes with the drive.

• Select the bay in which you want to install the drive.

• Check the instructions that come with the drive to determine whether you have to set any switches or

jumpers on the drive. If you are installing a SAS or SATA hard disk drive, be sure to set the SAS or
SATA ID for that device.

• You can install up to to eight 2.5-inch or four 3.5-inch hot-swap SAS or SATA hard disk drives in the server.

• The electromagnetic interference (EMI) integrity and cooling of the server are protected by having all bays

and PCI and PCI Express slots covered or occupied. When you install a drive, PCI, or PCI Express
adapter, save the EMC shield and filler panel from the bay or PCI or PCI Express adapter slot cover in the
event that you later remove the device.

• For a complete list of supported optional devices for the server, see

http://www.lenovo.com/us/en/serverproven/.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31.

To replace a hot-swap SAS or SATA hard disk drive, complete the following steps:

Note:

If you have only one hard disk drive, you must install it in the left drive bay.

Attention:

To avoid damage to the hard disk drive connectors, make sure that the server cover is in place

and fully closed whenever you install or remove a hard disk drive.

Step 1.

Remove the filler panel from the empty drive bay. Keep the filler panel in a safe place.

Step 2.

Touch the static-protective package that contains the drive to any unpainted metal surface on the
server; then, remove the drive from the package and place it on a static-protective surface.

Step 3.

Install the hard disk drive in the drive bay:

a.

Make sure that the tray handle is in the open (unlocked) position.

b.

Align the drive with the guide rails in the bay.

174

Lenovo System x3250 M5Installation and Service Guide

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands