Lenovo System x3250 M5 Installation And Service Manual Download Page 350

Page: 350 / 740

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0105

User Response

Information only; no action is required.

•

4000006a-00000000 : SSH Client key added for user [arg1].

User locally defined an SSH Client key

May also be shown as 4000006a00000000 or 0x4000006a00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0106

User Response

Information only; no action is required.

•

4000006b-00000000 : SSH Client key imported for user [arg1] from [arg2].

User imported an SSH Client key

May also be shown as 4000006b00000000 or 0x4000006b00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

336

Lenovo System x3250 M5Installation and Service Guide

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3250 M5

Reviews:

Brands by name

Popular brands

Lenovo System x3250 M5, Installation And Service Manual

Search results

Summary of Contents for System x3250 M5

Reviews:

Brands by name

Popular brands