manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

The Lenovo System x3250 M5 is a powerful server designed to deliver exceptional performance and reliability. To get started with your server, you can easily access the comprehensive Product Manual that provides detailed instructions and insights. Download it for free from our website and unleash the full potential of your Lenovo System x3250 M5.

Share
Download
background image

Serviceable

No

Automatically notify support

No

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0010

User Response

Information only; no action is required.

•

4000000b-00000000 : IP address of default gateway modified from [arg1] to [arg2] by user [arg3].

This message is for the use case where a user modifies the default gateway IP address of a Management
Controller.

May also be shown as 4000000b00000000 or 0x4000000b00000000

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0011

User Response

Information only; no action is required.

•

4000000c-00000000 : OS Watchdog response [arg1] by [arg2] .

This message is for the use case where an OS Watchdog has been enabled or disabled by a user.

May also be shown as 4000000c00000000 or 0x4000000c00000000

Severity

Warning

Serviceable

No

Appendix A. Integrated Management Module II (IMM2) error messages

289

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3250 M5

IBM BladeCenter S Installation And User Manual preview
BladeCenter S
Brand: IBM Pages: 84
IBM 9008-22L Manual preview
9008-22L
Brand: IBM Pages: 110
IBM LS42 - BladeCenter - 7902 Service Manual preview
LS42 - BladeCenter - 7902
Brand: IBM Pages: 194
Xblue Networks X-25 Installation Manual preview
X-25
Brand: Xblue Networks Pages: 148
NEC Express5800/320Fa-L User Manual preview
Express5800/320Fa-L
Brand: NEC Pages: 406
Supero SUPERSERVER 6028TP-HTFR User Manual preview
SUPERSERVER 6028TP-HTFR
Brand: Supero Pages: 141
Sun Microsystems Netra T2000 Service Manual preview
Netra T2000
Brand: Sun Microsystems Pages: 138
Supero SUPERSERVER 5017C-MF User Manual preview
SUPERSERVER 5017C-MF
Brand: Supero Pages: 96
Vidyo VidyoGateway Administrator'S Manual preview
VidyoGateway
Brand: Vidyo Pages: 186
SmartSight S1600e User Manual preview
S1600e
Brand: SmartSight Pages: 113
Kontron CP6006-SA User Manual preview
CP6006-SA
Brand: Kontron Pages: 90
NEC Express5800/R320f-E4 Installation Manual preview
Express5800/R320f-E4
Brand: NEC Pages: 88
Data-Tronix DT-HDIPCOM Installation & Configuration Manual preview
DT-HDIPCOM
Brand: Data-Tronix Pages: 29
Data-Tronix DT-HDIPUS User Manual & Installation Manual preview
DT-HDIPUS
Brand: Data-Tronix Pages: 30
NEC ExpressA1160 Brochure & Specs preview
ExpressA1160
Brand: NEC Pages: 4
NEC Express5800/T120e Specifications preview
Express5800/T120e
Brand: NEC Pages: 2
NEC Express5800/T120d Hardware Specificftion preview
Express5800/T120d
Brand: NEC Pages: 2
NEC Express5800/T110j System Configuration Manual preview
Express5800/T110j
Brand: NEC Pages: 32

Brands by name

Popular brands

Load more brands