manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

Share
Download
Lenovo System x3250 M5 Installation And Service Manual Download Page 207

Figure 122. ServeRAID SAS/SATA controller signal cable connection for hot-swap hard disk drive models
(left PCI module connection with two backplanes)

Step 3.

Make sure the relevant cables pass through the cable clips.

Step 4.

Align the ServeRAID SAS/SATA controller so that the keys align correctly with the connector on
the PCI riser-card assembly.

Step 5.

Insert the ServeRAID SAS/SATA controller into the connector on the PCI riser-card assembly
until it is firmly seated.

Attention:

Incomplete insertion might cause damage to the server or the ServeRAID SAS/SATA

controller.

Step 6.

Reinstall the PCI riser-card assembly (see “Replacing the PCI riser-card assembly” on page 163).

Step 7.

Reinstall the cover (see “Replacing the cover” on page 158).

What to do next

1. Install the server into the rack enclosure and push the server into the rack until it clicks into place.

2. Reconnect the power cords and any cables that you removed.

3. Turn on the peripheral devices and the server.

Chapter 6

.

Removing and replacing server components

193

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands