Lenovo System x3250 M5 Installation And Service Manual Download Page 370

Page: 370 / 740

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat the failing fan n, which is indicated by a lit LED near the fan connector on the system

board.

2. Replace the failing fan. (n = fan number)

•

80010204-1d05ffff : Numeric sensor [NumericSensorElementName] going low (lower critical)

has asserted. (Fan 5 Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d05ffff or 0x800102041d05ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat the failing fan n, which is indicated by a lit LED near the fan connector on the system

board.

2. Replace the failing fan. (n = fan number)

•

80010701-0701ffff : Numeric sensor [NumericSensorElementName] going high (upper non-critical)

has asserted. (PCI Temp)

This message is for the use case when an implementation has detected an Upper Non-critical sensor
going high has asserted.

May also be shown as 800107010701ffff or 0x800107010701ffff

Severity

356

Lenovo System x3250 M5Installation and Service Guide

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands

Lenovo System x3250 M5, Installation And Service Manual

Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands