manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

The Lenovo System x3250 M5 is a powerful server designed to deliver exceptional performance and reliability. To get started with your server, you can easily access the comprehensive Product Manual that provides detailed instructions and insights. Download it for free from our website and unleash the full potential of your Lenovo System x3250 M5.

Share
Download
background image

•

S.3040007 [S.3040007] A firmware fault has been detected in the UEFI image.

Explanation:

Internal UEFI Firmware Fault Detected, System halted

Severity

Error

User Response

Complete the following steps:

1. Check IBM Support website for an applicable service bulletin or firmware update that applies to

this error.

2.

Reflash UEFI image.

3. (Trained service technician only) Replace the system board.

•

S.3050007 [S.3050007] A firmware fault has been detected in the UEFI image.

Explanation:

Internal UEFI Firmware Fault Detected, System halted

Severity

Error

User Response

Complete the following steps:

1. Check IBM Support website for an applicable service bulletin or firmware update that applies to

this error.

2.

Reflash UEFI image.

3. (Trained service technician only) Replace the system board.

•

S.3058004 [S.3058004] A Three Strike boot failure has occurred. The system has booted with

default UEFI settings.

Explanation:

POST failure has occurred! System booted with default settings.

Severity

Error

User Response

Complete the following steps:

1. This event resets UEFI to the default settings for the next boot. If successful, user is forced into

F1 setup. Original UEFI settings are still present.

2. If User did not intentionally trigger the reboots, check logs for probable cause.

3. Undo recent system changes (settings or devices added). If not recent system changes, remove

all options then remove CMOS battery for 30 seconds to clear CMOS contents. Verify that the
system boots. Then, re-install options one at a time to locate the problem.

4. Check IBM Support website for an applicable service bulletin or firmware update that applies to

this error.

5.

Reflash UEFI firmware.

6. Remove and re-install CMOS battery for 30 seconds to clear CMOS contents

7. (Trained service technician only) Replace the system board.

538

Lenovo System x3250 M5Installation and Service Guide

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3250 M5

IBM BladeCenter S Installation And User Manual preview
BladeCenter S
Brand: IBM Pages: 84
IBM 9008-22L Manual preview
9008-22L
Brand: IBM Pages: 110
IBM 88723RU User Manual preview
88723RU
Brand: IBM Pages: 106
Vitek VT-IP2MSD102H Brochure preview
VT-IP2MSD102H
Brand: Vitek Pages: 2
Gigabyte R283-S93-AAF1 User Manual preview
R283-S93-AAF1
Brand: Gigabyte Pages: 115
PRIMERGY BX600 S2 Hardware Manual preview
BX600 S2
Brand: PRIMERGY Pages: 87
Supermicro SuperServer E300-9A-4C User Manual preview
SuperServer E300-9A-4C
Brand: Supermicro Pages: 109
Vxl Itona E21S Specifications preview
Itona E21S
Brand: Vxl Pages: 2
Gigabyte R292-4S0 User Manual preview
R292-4S0
Brand: Gigabyte Pages: 122
Atop ABLELink GW21W User Manual preview
ABLELink GW21W
Brand: Atop Pages: 52
Intel SC450NX - Server Platform - 0 MB RAM Product Manual preview
SC450NX - Server Platform - 0 MB RAM
Brand: Intel Pages: 200
Thecus N3200PRO User Manual preview
N3200PRO
Brand: Thecus Pages: 102
QNAP QBoat Sunny User Manual preview
QBoat Sunny
Brand: QNAP Pages: 39
Seagate 8-BAY RACKMOUNT NAS Quick Start Manual preview
8-BAY RACKMOUNT NAS
Brand: Seagate Pages: 20
Seagate BlackArmor NAS 420 User Manual preview
BlackArmor NAS 420
Brand: Seagate Pages: 64
Silex technology DS-510 Package Contents preview
DS-510
Brand: Silex technology Pages: 2
MRV Communications LX-8000 Series Manual preview
LX-8000 Series
Brand: MRV Communications Pages: 65
BCDVideo BCD221 User Manual preview
BCD221
Brand: BCDVideo Pages: 157

Brands by name

Popular brands

Load more brands