manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

Share
Download
Lenovo System x3250 M5 Installation And Service Manual Download Page 369

2. Replace the failing fan. (n = fan number)

•

80010204-1d03ffff : Numeric sensor [NumericSensorElementName] going low (lower critical)

has asserted. (Fan 3 Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d03ffff or 0x800102041d03ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Fan Failure

SNMP Trap ID

11

CIM Information

Prefix:

PLAT

ID:

0480

User Response

1. Reseat the failing fan n, which is indicated by a lit LED near the fan connector on the system

board.

2. Replace the failing fan. (n = fan number)

•

80010204-1d04ffff : Numeric sensor [NumericSensorElementName] going low (lower critical)

has asserted. (Fan 4 Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going
low has asserted.

May also be shown as 800102041d04ffff or 0x800102041d04ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Fan Failure

Appendix A. Integrated Management Module II (IMM2) error messages

355

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands