Lenovo System x3250 M5 Installation And Service Manual Download Page 498

Page: 498 / 740

•

816f0021-2582ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName]. (All PCI Error)

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed.

May also be shown as 816f00212582ffff or 0x816f00212582ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0331

User Response

No action; information only. One of PCI Error :

•

816f0021-3001ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName]. (PCI 1)

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed.

May also be shown as 816f00213001ffff or 0x816f00213001ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0331

User Response

No action; information only.

484

Lenovo System x3250 M5Installation and Service Guide

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands

Lenovo System x3250 M5, Installation And Service Manual

Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands