manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

The Lenovo System x3250 M5 is a powerful server designed to deliver exceptional performance and reliability. To get started with your server, you can easily access the comprehensive Product Manual that provides detailed instructions and insights. Download it for free from our website and unleash the full potential of your Lenovo System x3250 M5.

Share
Download
background image

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0128

User Response

Information only; no action is required.

•

40000081-00000000 : PXE boot requested by user [arg1].

PXE boot requested

May also be shown as 4000008100000000 or 0x4000008100000000

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0129

User Response

Information only; no action is required.

•

40000082-00000000 : The measured power value has returned below the power cap value.

Power exceeded cap recovered

May also be shown as 4000008200000000 or 0x4000008200000000

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

Warning - Power

SNMP Trap ID

Appendix A. Integrated Management Module II (IMM2) error messages

347

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3250 M5

IBM Power 570 Technical Overview And Introduction preview
Power 570
Brand: IBM Pages: 142
NTI ENVIROMUX-MINI Installation And Operation Manual preview
ENVIROMUX-MINI
Brand: NTI Pages: 35
IBM Netfinity Series Installation Instructions Manual preview
Netfinity Series
Brand: IBM Pages: 44
HPE ProLiant ML110 Gen 10 Product End-Of-Life Disassembly Instructions preview
ProLiant ML110 Gen 10
Brand: HPE Pages: 5
Fujitsu GP 7000F Manual preview
GP 7000F
Brand: Fujitsu Pages: 200
Brother HL-3400CN Series User Manual preview
HL-3400CN Series
Brand: Brother Pages: 280
Brother HL-6050DN Service Manual preview
HL-6050DN
Brand: Brother Pages: 308
Brother 2200W - NC Print Server Network User'S Manual preview
2200W - NC Print Server
Brand: Brother Pages: 75
Brother HL-6050DW Network User'S Manual preview
HL-6050DW
Brand: Brother Pages: 148
Brother HL-3400CN Series Service Manual preview
HL-3400CN Series
Brand: Brother Pages: 8
Bosanova RBT-320 Quick Start Manual preview
RBT-320
Brand: Bosanova Pages: 2
Dell EMC Boot Optimized Server Storage-S1 User Manual preview
Boot Optimized Server Storage-S1
Brand: Dell EMC Pages: 32
Advantech AGS-913 Series User Manual preview
AGS-913 Series
Brand: Advantech Pages: 100
exemys SSE232-IA User Manual preview
SSE232-IA
Brand: exemys Pages: 39
Gateway GT350 F1 Specifications preview
GT350 F1
Brand: Gateway Pages: 17
Gateway 910 Series System Manual preview
910 Series
Brand: Gateway Pages: 129
Sunfire V480 Administration Manual preview
V480
Brand: Sunfire Pages: 66
FaxFinder FF240 Administrator'S Manual preview
FF240
Brand: FaxFinder Pages: 116

Brands by name

Popular brands

Load more brands