Lenovo System x3250 M5 Installation And Service Manual Download Page 237 | Manualshive

Page: 237 / 740

background image

To remove the PCI riser-card bracket from the PCI riser-card assembly, complete the following steps.

Step 1.

Remove the cover (see “Removing the cover” on page 157).

Step 2.

Remove the PCI riser-card assembly (see “Removing the PCI riser-card assembly” on page 163).

Step 3.

Remove the screws that attach the PCI riser card to the riser-card bracket.

Figure 150. PCI riser-card bracket removal

If you are instructed to return the server component or optional device, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing the PCI riser-card bracket to the PCI riser-card assembly

Use this information to replace the PCI riser-card bracket to the PCI riser-card assembly.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31 .

If you are replacing a server component in the server, you need to slide the server out from the rack
enclosure, turn off the server and peripheral devices, and disconnect the power cords and all external cables.

To replace the PCI riser-card bracket to the PCI riser-card assembly, complete the following steps.

Step 1.

Align the holes on the PCI riser card and the riser-card bracket and install the screws that attach
the PCI riser card to the riser-card bracket.

Removing and replacing server components

223

«
...
235
236
237
238
239
...
»

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3250 M5

Brand: A10 Networks Pages: 17

Brand: Sun Microsystems Pages: 128

Brand: Kontron Pages: 110

Transport GT26-B4987

Brand: TYAN Pages: 125

ANR-C62-N1 Series

Brand: Acrosser Technology Pages: 57

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Brand: LaCie Pages: 74

DIGI CONNECT ES

Brand: Digi Pages: 23

Brand: Hitachi Pages: 208

Brand: Hitachi Pages: 36

Brand: Digi Pages: 118

Brand: QNAP Pages: 69

NET-SERV Series

Brand: Panduit Pages: 24

Brand: ICP DAS USA Pages: 26

Brand: innuos Pages: 10

Brand: Terra Pages: 22

Brand: Satel Pages: 8

NetFrame 5200 Series

Brand: Micron Pages: 17

Brand: Supero Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands