Lenovo System x3250 M5 Installation And Service Manual Download Page 482

Page: 482 / 740

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 810702010301ffff or 0x810702010301ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only.

•

81070201-0701ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (VR Hot)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 810702010701ffff or 0x810702010701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only.

468

Lenovo System x3250 M5Installation and Service Guide

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3250 M5

Reviews:

Brands by name

Popular brands

Lenovo System x3250 M5, Installation And Service Manual

Search results

Summary of Contents for System x3250 M5

Reviews:

Brands by name

Popular brands