Lenovo System x3250 M5 Installation And Service Manual Download Page 605

Page: 605 / 740

Severity

Warning

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-801-000 : MLNX:MLNX_DiagnosticTestIBPort Test Aborted

Port Test was canceled.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-900-000 : MLNX:MLNX_DiagnosticTestEthernetPort Test Failed

Port Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Make sure that the physical link of the port under test in the active state.

2. If these condition was met but the test keeps failing the port's adapter might be faulty.

Appendix C. DSA diagnostic test results

591

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands

Lenovo System x3250 M5, Installation And Service Manual

Search results

Summary of Contents for System x3250 M5

Reviews:

Related manuals for System x3250 M5

Brands by name

Popular brands