8/29
Technical data sheet: S000074637EN-5
Updated: 12/03/2015
Created: 15/04/2014
Technical data sheet
Catalogue number(s): 0 484 22
KNX multiapplication controller 16 outputs
KNX multiapp
8. COmmUNiCaTiON OBJECTS (CONTiNUED)
8. COmmUNiCa
This function is used, for binary inputs to which a push button is atta-
ched, to send a switching telegram (ON, OFF or TOGGLE) as a reaction to
a short or long push button action, i.e. this function can be used e.g. to
recall a scene.
Parameters
Setting
Short push reaction
No reaction
On
Off
Toggle
Here an adjustment is made to define which switching value is written
into the storage cell of the communication object and sent after short
pressing of the push attached to the input.
“No reaction”: A short push button action does not change the object
value and also does not send a telegram.
“
On”: After a short push, the switching value “ON” (binary value, “1”) is
transferred into the communication object and sent.
“
Off”: After a short push, the switching value “OFF” (binary value,”0”) is
transferred into the communication object and sent.
“Toggle” : After a short push, the switching value stored in the commu-
nication object is inverted and the new value is sent.
Long push reaction
No reaction
On
Off
Toggle
Here an adjustment is made to define which switching value is written
into the storage cell of the communication object and sent after long
pressing the push button attached to the input.
“No reaction”: A long push does not change the object value and also
does not lead to the sending of a telegram.
“
On”: After a long push, the switching value “ON” (binary value, “1”) is
transferred into the communication object and sent.
“
Off” : After a long push, the switching value “OFF” (binary value,”0”) is
transferred into the communication object and sent.
“Toggle” : After a long push, the switching value stored in the commu-
nication object is inverted and the new value is sent.
Long push action min.
0.5 second
1 second
2 seconds
3 seconds
4 seconds
5 seconds
10 seconds
This parameter determines the minimum period for detecting a long
push.
add status object
Yes /
No
The parameter determines if an additional communication object (sta-
tus) shall be used to perform toggle functionality or other purposes.
Contact type
Normally open contact
Normally closed contact
The contact type of the input attached to the channel is adjusted here.
“Normally open contact” : the contact of the input is active when
closed, inactive when opened.
“Normally closed contact” : the contact of the input is active when
opened, inactive when closed.
add enable object
Yes /
No
The parameter determines if the input can be blocked via an additional
Enable object or not. If an input is blocked (Enable value = 0) the status
changes at this input are not transmitted.
Parameters
Switching value whe
Here an adjustment
written into the stor
after a rising edge. T
signal status at the i
“No reaction”: action
not send a telegram
“Up”: when the con
the communication
“Down
”: when the c
into the communica
Switching value whe
opened
Here an adjustment
command is written
and sent after a falling
The falling edge cor
input from logical “1
“No reaction”: action
not send a telegram
“Stop”: when the con
into the communica
Contact type
The contact type of
“Normally open con
closed, inactive whe
“Normally closed con
opened, inactive wh
add enable object
The parameter deter
Enable object or no
changes at this input
•
Push
This function allows usin
down, stopping of the
this a distinction is ma
Shutter 1-input
No.
Object name
function
Size
flags
2
(9, 16, 23,
30, 37, 44,
51, 58, 65,
72, 79, 86,
93, 100,
107)
Input G(,H)1 (2
8) Shutter Up/
Down
1.008 DPT_
UpDown
CWT
The movement commands Up/Down are sent via the address linked
with this object in order to raise/lower the solar protection.
8
(15, 22,
29, 36, 43,
50, 57, 64,
71, 78, 85,
92, 99,
106, 113)
Input G(,H)1 (2
8) Shutter Stop
- slats
1.009 DPT_
OpenClose
CWT
The command “STOP” or “Slats OPEN/CLOSE” are sent via the group
address linked with this object.
4
(11, 18,
25, 32, 39,
46, 53, 60,
67, 74, 81,
88, 95,
102, 109)
Input G(,H)1 (2
8) Enable
1.003 DPT_
Enable
CW
Enable telegrams are received via the group address linked with this
object. They are used to lock (disable) or unlock (enable) the correspon-
ding input.
They are only visible if“Add enable object”parameter value is set to yes.
•
Switch
This function allows using just one swich for moving a shutter up or
down and to stop its motion. To achieve this a distinction is made
between closed and open contact action.
S000074637EN-5.indd 8
20/05/15 10:16
