20/29
Technical data sheet: S000074637EN-5
Updated: 12/03/2015
Created: 15/04/2014
Technical data sheet
Catalogue number(s): 0 484 22
KNX multiapplication controller 16 outputs
KNX multiapp
8. COmmUNiCa
8. COmmUNiCaTiON OBJECTS (CONTiNUED)
Parameters
Setting
Xn : Invert enable logic
Yes /
No
The Enable logic of the output attached to the channel is adjusted
here.
“No
”: the contact of the output is Disable when “Output Xn, Enable”
object value is 0.
“Yes
”: the contact of the output is Disable when “Output Xn, Enable”
object value is 1.
8.2.2 Shutter (for Ports A and B only)
No.
Object name
function
Size
flags
114,122
Outputs A (B)
Shutter Up/
Down
1.008 DPT_
UpDown
CW
The Up/Down movement for the corresponding channel is initiated via
these objects. The shutter is raised on receipt of a logical 0 and lowered
on receipt of a logical 1. The drive mechanism remains switched on
until either a stop command is received
115,123
Outputs A (B)
Open/Close
Slats
1.009 DPT_
OpenClose
CW
Shutter Stop
Via these objects, the movement of a blind/shutter is stopped
regardless of whether the telegram contains a logical 0 or a logical 1.
If the output is configured as "Venitian blind" and the blind is statio-
nary, the slats are opened by one step on receipt of a logical 0 and
closed by one step on receipt of a logical 1.
If the output is configured as "Roller shutter" and a stop command is
received when the roller shutter is stationary, the command is ignored.
117,125
Outputs A (B)
Shutter
Alarm
1.005 DPT_
Alarm
CW
This object can be linked with an alarm signal from a wind, rain or ice
detector, which sends a logical 0 in the idle state and a logical 1 in the
event of an alarm.
116,124
Outputs A (B)
Shutter
Enable
1.003 DPT_
Enable
CW
Enable telegrams are received via the group address linked with this
object. They are used to lock (disable) or unlock (enable) the correspon-
ding input.
In ventian blind use you have the parameters for slat control
Parameters
Setting
Xn+(n+1) Usage
Use separately(*)
Venitian blind
Roller shutter
Exclusive function
Slat time (base 100ms)
3
(0
255)
Only available if “Xn+(n+1) Usage” is set to “Venitian blind”
Parameters
Setting
Up to Down time (base 1s)
30
(0
255)
Only available if “Xn+(n+1) Usage” is set to “Venitian blind” or “Roller
shutter”
Behaviour on alarm
No action
Move up
Move down
Only available if “Xn+(n+1) Usage” is set to “Venitian blind” or “Roller
shutter”
Invert relay polarity
Yes /
No
Allows to invert the move up/down command.
“No”: X1 is move up, X2 move down
“Yes”: X1 is move down, X2 is move up
Invert Enable logic
Yes /
No
The Enable logic of the output attached to the channel is adjusted
here.
“No
”: the contact of the output is Disable when “Output Xn, Enable”
object value is 0.
“Yes
”: the contact of the output is Disable when “Output Xn, Enable”
object value is 1.
(*): See the previous parameters description and communication object
description table
8.2.3 Exclusive function (Ports A and B only)
This functionality is used to perform logical XOR functions between two
relays on the same port.
No.
Object name
function
Size
flags
115 (122)
Outputs A (B)
A2 on & A1
off | Off
(B2 on & B1
off | Off)
1.002 DPT_
Bool
CW
1 : Activates A2, Deactivates A1
0 : Deactivates A1 and A2
114 (123)
Outputs A (B)
A1 on & A2
off | Off
(B1 on & B2
off | Off)
1.002 DPT_
Bool
CW
1 : Activates A1, Deactivates A2
0 : Deactivates A1 and A2
121 (129)
Outputs A (B)
A2 Status
(B2 Status)
1.002 DPT_
Bool
CRT
1 : A2 (B2) is activated
0 : A2 (B2) is deactivated
117 (125)
Outputs A (B)
A1 Status
(B1 Status)
1.002 DPT_
Bool
CRT
1 : A1 (B1) is activated
0 : A1 (B1) is deactivated
Parameters
Setting
Xn, Invert relay polarity
Yes /
No
Allows to invert the logic of the exclusive function
8.2.4 Dali
No.
Object n
178
DALI
This object is used to
red to the DALI bus
Switching telegrams
object.
179
DALI
The current switchin
It is automatically sen
180
DALI
This object is used to
red to the DALI bus
Level value telegram
object.
181
DALI
The current level sta
automatically sent each
184
DALI
Dimming control te
with this object.
182
DALI
Enable telegrams ar
object. They are use
ding input.
183
DALI
Override telegrams
object.
Output Xn can be for
value of the commu
of the contact:
0 or 1 = The output is not f
2 = The output is for
3 = The output is for
S000074637EN-5.indd 20
20/05/15 10:16