14/29
15/29
Technical data sheet: S000074637EN-5
Updated: 12/03/2015
Created: 15/04/2014
mber(s): 0 484 22
Catalogue number(s): 0 484 22
KNX multiapplication controller 16 outputs
1
ned 8-bit value is
object and sent
channel (input). The rising
t the input from
ormally open contact
y closed contact
o the channel is adjusted here.
t of the input is active when
t of the input is active when
blocked via an additional
f an input is blocked (Enable value = 0) the status
e
flags
0
DPT_Va-
ue_1_
ount
CT
the group address
003 DPT_
ble
CW
linked with this
(enable) the correspon-
value is set to yes.
a byte value tele-
sent.
Parameters
Setting
Byte value when contact is closed
0
255,
1
Here an adjustment is made to define which unsigned unsigned 8-bit
value is written into the storage cell of the communication object and
sent after a rising edge in the signal status at the channel (input). The
rising edge corresponds to a change in the signal status at the input
from logical “0” to “1”.
Byte value when contact is opened
0
255,
0
Here an adjustment is made to define which unsigned 8-bit value is
written into the storage cell of the communication object and sent
after a falling edge in the signal status at the channel (input). The
falling edge corresponds to a change in the signal status at the input
from logical “1” to “0”.
Contact type
Normally open contact
Normally closed contact
The contact type of the input attached to the channel is adjusted here.
“Normally open contact”: the contact of the input is active when
closed, inactive when opened.
“Normally closed contact”: the contact of the input is active when
opened, inactive when closed.
add enable object
Yes / No
The parameter determines if the input can be blocked via an additional
Enable object or not. If an input is blocked (Enable value = 0) the status
changes at this input are not transmitted.
•
Push
This function is used for inputs with a push button to send a byte value tele-
gram, the push is short or long, a telegram is sent.
Parameters
Setting
Byte value on short push
0
255,
1
Here an adjustment is made to define which unsigned 8-bit value is
written into the storage cell of the communication object and sent
after short pressing the push button attached to the input.
Byte value on long push
0
255,
0
Here an adjustment is made to define which unsigned 8-bit value is
written into the storage cell of the communication object and sent
after long pressing the push button attached to the input.
Long push action min.
0.5 second
1 second
2 seconds
3 seconds
4 seconds
5 seconds
10 seconds
This parameter determines the minimum period for detecting a long
push.
Contact type
Normally open contact
Normally closed contact
The contact type of the input attached to the channel is adjusted here.
“Normally open contact”: the contact of the input is active when
closed, inactive when opened.
“Normally closed contact”: the contact of the input is active when
opened, inactive when closed.
Parameters
Setting
add enable object
Yes / No
The parameter determines if the input can be blocked via an additional
Enable object or not. If an input is blocked (Enable value = 0) the status
changes at this input are not transmitted.
8.1.2 Use Jointy
Dimming
No.
Object name
function
Size
flags
2
(16, 30,
44, 58, 72,
86, 100)
Input G(,H)1 (3
7)+
G(,H)2 (4
8),
Switching
1.001 DPT_
Switch
CWT
Switching telegrams are sent via the group address linked with this
object.
6
(20, 34,
48, 62, 76,
90, 104)
Input G(,H)1 (3
7)+
G(,H)2 (4
8)
Dimming
3.007 DPT_
Control_Dim-
ming
CT
Dimming telegrams are sent via the group address linked with this
object.
7
(21, 35,
49, 63, 77,
91, 105)
Input G(,H)1 (3
7)+
G(,H)2 (4
8)
Value Status 5.001 DPT_
Scaling
CW
The dimming status telegrams are received from the dimming actuator
via the group address linked with this object. This object is only visible
when the parameter“Add status object”is set to“yes”.
4
(18, 32,
46, 60, 74,
88, 102)
Input G(,H)1 (3
7)+
G(,H)2 (4
8)
Enable
1.003 DPT_
Enable
CW
Enable telegrams are received via the group address linked with this
object. They are used to lock (disable) or unlock (enable) the correspon-
ding input.
They are only visible if“Add enable object”parameter value is set to yes.
8. COmmUNiCaTiON OBJECTS (CONTiNUED)
S000074637EN-5.indd 15
20/05/15 10:16
