28/29
Technical data sheet: S000074637EN-5
Updated: 12/03/2015
Created: 15/04/2014
Technical data sheet
Catalogue number(s): 0 484 22
KNX multiapplication controller 16 outputs
KNX multiapp
8. COmmUNiCa
8. COmmUNiCaTiON OBJECTS (CONTiNUED)
Parameters
Setting
Output result
Logic Result
Fixed value
This is a parameter that determines which kind of value should be sent
into Logic Fn Output object. It can be the logic operation result or a
preset value (fixed value).
Output Send
-
Condition
Result change
Result is true
Result is false
Input 1 event
Input 2 event
Input 3 event
Input 1 or 2 or 3 event
Here it is posible to make a parameter that determines the trigger
condition of the Logic Fn Output object telegram sending.
input 1 Size
1 bit
2 bits
4 bits
1 Byte
2 Bytes
4 Bytes
Here it is posible to make an adjustment to set the datapoint size of the
“Logic Fn Output” communication object.
value 1 Type
"Input Size" value
Possible setting values
1 bit
Value
On/Off
Enable/Disable
Up/Down
2 bits
Value
Control Value
4 bits
Value
Dimming
1 Byte
Non-scaled value
Scaled value
Scene
2 Bytes
Unsigned value
Floating value
4 Bytes
Unsigned value
Floating value
Here it is posible to make an adjustment to set the datapoint type of
the comparison element.
value 1
1 bit | Value
0, 1
1 bit On/Off
On, Off
1 bit Enable/Disable
Enable / Disable
1 bit Up/Down
Up / Down
2 bits Value
0, 1, 2, 3
2 bits Control Value
Priority High / On
Priority High / Off
Priority Low / On
Priority Low / Off
4 bits Value
0
15
4 bits Dimming
Up 100%, Up 50%,
Up 25%, Up 12%, Up 6%,
Up 3%, Up 1%, Stop, Stop,
Down 1%, Down 3%,
Down 6%, Down 12%,
Down 25%, Down 50%
1 Byte Non-scaled value 0
255
1 Byte Scaled value
0
100%
1 Byte Scene
1
64
2 Bytes Unsigned value
0
65535
2 Bytes Floating value
0
65535
4 Bytes Unsigned value
0
4294967295
4 Bytes Floating value
0
4294967295
This is an adjustment to set the value that should be compared to
Logic Fn Input XXX value.
Output delay param
a) Without any delay
On
Switching
telegrams
Relay contact
b) Delay before ON
Switching
telegrams
Relay contact
On
Of
Time delay
c) Delay before OFF
Switching
telegrams
Relay contact
On
Of
Time delay
d) Delay before OFF
Switching
telegrams
Relay contact
On Off
Time delay
e) Auto Switch OFF
Switching
telegrams
Relay contact
On Off
Time delay
f) Delay before ON + A
Switching
telegrams
Relay contact
On Off
Time delay
g) Delay before OFF + A
Switching
telegrams
Relay contact
On
Time delay
Output
Value 1
Input value 1
Comparator 1
Comparator 1
Operator 1
Output
Value 1
Value 2
Comparator 2
Input value 1
Input value 2
Comparator 1
Operator 1
Operator 2
Output
Value 1
Value 2
Value 3
Comparator 2
Comparator 3
Input value 1
Input value 2
Input value 3
Synoptic: output behaviours
Enable
Cmd
value
Bit 1
Bit 0
Override 2bits
Enable / Disable
On / Off
On / Off status
t
Scene manager
(2)
Mode Manager
(1)
Mode
Priority
(1)
&
Override
&
Scenes
&
Cmd
t
Scene
Mode
(1)
mode manager
Four modes are applicable. Each mode determines if the output should
be available or not (very high priority) If the output is inactive, the
output cannot be managed by any object as long as the current mode is
active, otherwise, objects “Scene”, “Override”, “Enable/Disable”, “On/Off”
are usable.
It’s possible to determine the action to do when the desired mode is
launched.
(2)
Scene manager
Each output can be assigned to 5 instances of scenes. An instance scene
is defined by a scene number and a value preset. If the scene number is
set to the value “0”, the scene instance is not used.
Scenes action can be executed after a time delay. This time delay is
independent and overrides the outputs’ delay parameters “time before
off” and “time before on”.
S000074637EN-5.indd 28
20/05/15 10:16
