KYMCO Downtown 300i ABS Service Manual Download Page 99 | Manualshive

Page: 99 / 263

background image

8. DRIVE AND DRIVEN PULLEYS/

V-BELT

8-11

Downtown 300i ABS

Install the movable driven face onto the
driven face.
Apply grease to the guide rollers and guide
roller pins and then install them into the holes
of the driven face.

Install the seal collar.
Remove any excessive grease.

Set the driven pulley assembly, driven face
spring and clutch assembly onto the clutch
spring compressor.

Compress the tool and install the drive plate
nut.

Set the tool in a vise and tighten the drive
plate nut to the specified torque.

Torque

: 75 N-m

Clutch Spring Compressor E053
Fittings & Nut Wrench, 41mm E033

•

Be sure to clean the driven face off any
grease.

＊

•

Align the flat surface of the driven face
with the flat on the clutch drive plate.

＊

•

Be sure to use a clutch spring
compressor to avoid spring damage.

＊

Special

Guide Pins

Grooves

Clutch/Driven Pulley

Clutch Spring Compressor

Lock Nut Wrench

«
...
97
98
99
100
101
...
»

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Related manuals for Downtown 300i ABS

990D0-28K50-CLE

Brand: Suzuki Pages: 12

Brand: Clas Ohlson Pages: 5

Daytona 675 2014

Brand: Triumph Pages: 162

Brand: GPX Pages: 44

Brand: DYNATEK Pages: 1

Brand: DYNATEK Pages: 8

Brand: Yamaha Pages: 400

Intruder VS1400

Brand: Suzuki Pages: 291

Brand: probrake Pages: 2

Brand: probrake Pages: 2

Brand: Datatool Pages: 9

Brand: APRILIA Pages: 279

FuelGaugePro FGP-SENSOR

Brand: LSK Pages: 11

Brand: RIEJU Pages: 7

Brand: Denali Pages: 3

Brand: MT Helmets Pages: 116

PEGASO 650 TRAIL

Brand: APRILIA Pages: 12

Brand: KTM Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands