manualshive.com logo in svg

KYMCO Downtown 300i ABS, Service Manual

Share
Download
KYMCO Downtown 300i ABS Service Manual Download Page 246

20

. 

EVAPORATIVE EMISSION CONTROL SYSTEM

Downtown 300i ABS

PURGE CONTROL VALVE FLOW
INSPECTION

1. Connect a vacuum pump to the purge

control valve vacuum tube and apply
vacuum pressure of 45mm/Hg.

2. Connect a pressure pump to the tube that

goes to the charcoal canister and apply
pressure. The flow must be over 9.4 liters
per minute and replace the purge control
valve with a new one if the specified flow
is not reached.

INSTALLATION

1. Install the purge control valve in the

reverse order of removal.

2. Route and reconnect the purge control

valve tubes properly and securely.

To prevent damage to the purge control
valve, do not use high air pressure
sources. Use a hand operated pressure
pump only.

＊

Be careful not to bend, twist or kink the
tubes during installation.

＊

Pressure Pump

Vacuum Pump

20-5

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands