manualshive.com logo in svg

KYMCO Downtown 300i ABS, Service Manual

Share
Download
KYMCO Downtown 300i ABS Service Manual Download Page 162

  13. FUEL INJECTION SYSTEM

     

13-25

Downtown 300i ABS

TPS INSPECTION

Support the scooter on a level surface.
Put the side stand up and engine stop switch
is at “RUN”.
Turn the ignition switch to “ON”.
Measure if the ECU voltage outputs to TPS
between the following terminals of the TPS
connector.

Terminal

Normal

Violet/Red (+) – Green/Pink (-)

5 V

Throttle position sensor (TPS) resistance
(at 20°C/68°F)       3500~6500

Ω

REMOVAL

Loosen the throttle cables with the adjusting
nuts.
Disconnect the throttle cable ends from
throttle seat.

Disconnect the TPS, ISC and MAP sensor
connectors.
Loosen the air cleaner connecting hose band
screw.
Loosen the intake manifold band screw.
Remove the throttle body, MAP sensor, TPS
sensor and ISC sensor as a set.

                                                        TPS

                            Cable Ends

Adjusting Nuts

                      ISC Sensor    MAP Sensor

              TPS Sensor

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands