manualshive.com logo in svg

KYMCO Downtown 300i ABS, Service Manual

Share
Download
KYMCO Downtown 300i ABS Service Manual Download Page 189

14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/

FRONT SHOCK ABSORBER/STEERING STEM

14-9

Downtown 300i ABS

FRONT BRAKE FLUID 

FLUID REPLACEMENT/AIR
BLEEDING

BRAKE FLUID DRAINING

Make sure that the master cylinder parallel to
the ground before removing the reservoir
cover.

Remove two screws.

Remove the reservoir cover, diaphragm plate
and diaphragm.

Connect a bleed hose to the bleed valve. 

●

 

A contaminated brake disc or pad
reduces stopping power. Discard
contaminated pads and clean a
contaminated disc with a high quality
brake degreasing agent.

●

 

Do not allow foreign material to enter
the system when filling the reservoir.

●

 

Avoid spilling brake fluid on painted,
plastic or rubber parts. Place a rag
over these parts whenever the system
is serviced.

＊

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands