KYMCO Downtown 300i ABS Service Manual Download Page 63

Page: 63 / 263

. ENGINE REMOVAL/INSTALLATION

5-2

Downtown 300i ABS

ENGINE
REMOVAL/INSTALLATION

REMOVAL

Remove the air cleaner

Disconnect the connector including of ISC,
Throttle body, TPS, WTS, MAP sensor and
injector.

Disconnect the O2 sensor connector.

Disconnect the throttle cables.

Disconnect the Regulator/Rectifier
connector.

Disconnect the starter relay wire from
starter motor.

Remove a bolt from fuel hose guide.

Disconnect the fuel hose from fuel injector.

Disconnect the input water hose.

Disconnect the air bleed hose.

Fuel hose guide

Water pump

Oil filter

Water hose

Summary of Contents for Downtown 300i ABS








































































































































































































































































Search results

Summary of Contents for Downtown 300i ABS

Reviews:

Related manuals for Downtown 300i ABS

Brands by name

Popular brands

KYMCO Downtown 300i ABS, Service Manual

Search results

Summary of Contents for Downtown 300i ABS

Reviews:

Related manuals for Downtown 300i ABS

Brands by name

Popular brands