manualshive.com logo in svg

KYMCO Downtown 300i ABS, Service Manual

Share
Download
KYMCO Downtown 300i ABS Service Manual Download Page 187

14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/

FRONT SHOCK ABSORBER/STEERING STEM

14-7

Downtown 300i ABS

INSTALLATION

Apply grease to the collar, then install the
collar onto the wheel.

Install the speedometer speed wheel sensor. 

  DISASSEMBLY

Remove the side collar and dust seal.

Turn the inner race of each bearing with your
finger to see if they turn smoothly and quietly.
Also check if the outer race fits tightly in the
hub.

Replace the bearings if the races do not turn
smoothly, quietly, or if they fit loosely in the
hub.

Remove the front wheel bearing by using the
special tool.

Special tool:

Bearing puller

E00037

Remove the distance collar from wheel.

Collar

Speed Wheel Sensor

Dust Seal

Bearing

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands