manualshive.com logo in svg

KYMCO Downtown 300i ABS, Service Manual

Share
Download
KYMCO Downtown 300i ABS Service Manual Download Page 45

3. INSPECTION/ADJUSTMENT

 

3-4

Downtown 300i ABS

ENGINE OIL

OIL LEVEL INSPECTION

Stop the engine and support the scooter
upright on the level ground.
Wait for 2

～

3 minutes and check the oil level

with the dipstick. Do not screw in the dipstick
when checking the oil level.

OIL CHANGE

Remove the oil drain bolt to drain the engine
oil.
Install the aluminum washer and tighten the
oil drain bolt.

Torque:

 2.5 kg-m

Pour the recommended oil through the oil
filler hole.

OIL CAPACITY

Engine oil capacity:    1.5 L
Engine oil exchanging capacity: 1.3 L
Engine Oil Viscosity : SAE 5W50

OIL FILTER SCREEN INSPECTION

Drain the engine oil.
Remove the oil filter screen attaching the left-
under crankcase.
Clean the oil filter screen.
Install the oil filter screen and filter screen
cap.
Fill the engine with recommended engine oil.

OIL FILTER REPLACEMENT

Remove the oil filler cap attaching the right-
under crankcase cover.

Replace the aluminum washer with a
new one if it is deformed or damaged.

＊

Oil Drain Bolt

Oil Filter Screen

Oil Filter Cap

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands