KYMCO Downtown 300i ABS Service Manual Download Page 185

Page: 185 / 263

14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/

FRONT SHOCK ABSORBER/STEERING STEM

14-5

Downtown 300i ABS

Remove two screws and then remove the left
handlebar switch.

ASSEMBLY

Install the left handlebar switch.

Install and tighten the two screws securely.

Install the right handlebar switch.

Lubricate the throttle grip front end with
grease and then connect the throttle cable to
the throttle grip.

Install and tighten the two screws.

Align the pin on the left handlebar switch
with the hole on the handlebar.

＊

Align the pin on the right handlebar
switch with the hole on the handlebar.

＊

Screws

Summary of Contents for Downtown 300i ABS








































































































































































































































































Search results

Summary of Contents for Downtown 300i ABS

Reviews:

Brands by name

Popular brands

KYMCO Downtown 300i ABS, Service Manual

Search results

Summary of Contents for Downtown 300i ABS

Reviews:

Brands by name

Popular brands