manualshive.com logo in svg

KYMCO Downtown 300i ABS, Service Manual

Share
Download
KYMCO Downtown 300i ABS Service Manual Download Page 197

14.HANDLEBAR/FRONT WHEEL/FRONT BRAKE/

FRONT SHOCK ABSORBER/STEERING STEM

14-17

Downtown 300i ABS

INSTALLATION

Install the new bottom cone race onto the
steering stem.
Install the new upper and bottom ball races
into the frame.
Apply grease to the top and bottom ball races
and install new steel balls on the top ball race
and new steel balls on the bottom ball race.
Install the steering stem.

Apply grease to the top cone race and install
it.
Tighten the top cone race and then turn the
steering stem right and left several times to
make steel balls contact each other closely.

Special tool:

Lock nut wrench

F00023

Install the steering stem lock nut and tighten
it to the specified torque by using the special
tool while holding the top cone race.

Torque

: 7 kgf-m (70 N-m)

Special tool:

Lock nut wrench

F00002

Check the steering stem rotates freely
without vertical play.

＊

Bottom Ball Race

Remove 

special tool

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands