manualshive.com logo in svg

KYMCO Downtown 300i ABS, Service Manual

Share
Download
KYMCO Downtown 300i ABS Service Manual Download Page 131

12. COOLING SYSTEM

     

12-7

Downtown 300i ABS

THERMOSTATIC SWITCH 

When the coolant temperature is lower than
85 

℃

, the thermostatic switch OFF.

When coolant temperature is over 90 

℃

,

the thermostatic switch ON.

RADIATOR INSTALLATION

Install the fan rubber on the radiator with
three bolts.
Install the radiator on the radiator bracket
with three bolts/nuts.
Connect the upper and lower hoses and
secure them with hose bands.
Connect the thermostatic switch wire.
Connect the fan motor wire couplers.
Connect the overflow tube and secure with
the tube clamp.
Fill the radiator with coolant. 
Connect the vent tube to the radiator filler.
After installation, check for coolant leaks.
Connect the outlet tube of the reservoir and
secure with the tube clamp.

If you want to refill the coolant, the
following procedure must be checked.
1. Please make the radiator filler and

the air vent tube to be separated.

2.

 

Start the engine, filled in the coolant
till the coolant flowed out from the air
vent tube.

＊

Thermostatic Switch

Air Vent Tube

Overflow Tube

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands