KYMCO Downtown 300i ABS Service Manual Download Page 47 | Manualshive

Page: 47 / 263

background image

3. INSPECTION/ADJUSTMENT

3-6

Downtown 300i ABS

AIR CLEANER

AIR FILTER REPLACEMENT

Remove the body cover.
Remove seven screws attaching to the air
cleaner cover.
Remove six screws attaching to the filter.
Check the filter and replace it if it is
excessively dirty or damaged.

CHANGE INTERVAL

More frequent replacement is required when
riding in unusually dusty or rainy areas.

SPARK PLUG

Remove the spark plug cap and spark plug.
Check the spark plug for wear and fouling
deposits.
Clean any fouling deposits with a spark plug
cleaner or a wire brush.

Specified Spark Plug

: NGK-CR7E

Measure the spark plug gap.

Spark Plug Gap

: 0.6 – 0.7 mm

Torque

:17.2 N-m



The air cleaner element has a viscous
type paper element. Do not clean it
with compressed air.



Be sure to install the air cleaner
element and cover securely.

＊



When installing, first screw in the spark
plug by hand and then tighten it with a
spark plug wrench.

＊

Air Cleaner Cover

Deformation

0.6~0.7 mm

｝

Gap
Wear
Fouling
Deposits

Cracks
Damage

Spark Plug

«
...
45
46
47
48
49
...
»

Summary of Contents for Downtown 300i ABS








































































































































































































































































Reviews:

No comments

Related manuals for Downtown 300i ABS

750 Sport Bevel Heaven

Brand: Ducati Pages: 235

Brand: R&G Pages: 12

Brand: J&M Pages: 5

65175810022-00-40

Brand: hepco & becker Pages: 4

2016 Empulse TT

Brand: Victory Motorcycles Pages: 138

Daytona 955i 2002

Brand: Triumph Pages: 384

Brand: Crivit Pages: 58

Freeride 350 2013

Brand: KTM Pages: 113

6513515 00 22-00-40

Brand: hepco & becker Pages: 7

Brand: R&G Pages: 8

Brand: oset Pages: 44

Brand: Öhlins Pages: 2

640 LC4 Adventure

Brand: KTM Pages: 59

Brand: hepco & becker Pages: 4

Brand: Triumph Pages: 126

Brand: Saddlemen Pages: 6

Brand: Yamaha Pages: 34

Brand: Yamaha Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands