KYMCO Downtown 300i ABS Service Manual Download Page 87

Page: 87 / 263

7. CYLINDER/PISTON

7-7

Downtown 300i ABS

PISTON INSTALLATION

Remove any gasket material from the
crankcase surface.

Install the piston, piston pin and a new
piston pin clip.

CYLINDER INSTALLATION

Install the dowel pins and a new cylinder
gasket on the crankcase.

•

Be careful not to drop foreign matters
into the crankcase.

＊

•

Position the piston “IN” mark on the
intake valve side.

•

Place a clean towel in the crankcase to
keep the piston pin clip from falling into
the crankcase.

＊

The piston must be changed in pair

with cylinder.

＊

Piston

Summary of Contents for Downtown 300i ABS








































































































































































































































































Search results

Summary of Contents for Downtown 300i ABS

Reviews:

Related manuals for Downtown 300i ABS

Brands by name

Popular brands

KYMCO Downtown 300i ABS, Service Manual

Search results

Summary of Contents for Downtown 300i ABS

Reviews:

Related manuals for Downtown 300i ABS

Brands by name

Popular brands