KVH Industries TracPhone FB150 User Manual Download

Page: 129 / 140

Chapter 5: Troubleshooting

Reset button

120

Reset button

How to access the Reset button

The terminal has a Reset button placed next to the SIM slot behind the SIM cover.

The functions of this button is described in the next section.
To press the Reset button, use a pointed device.

Function of the Reset button

The Reset button on the terminal has the following functions:

Action

Function

With the terminal

running, press the Reset

button normally.

The terminal IP address and IP netmask are

temporarily set to the default value (default IP

address: 192.168.0.1).
With this function, even if the IP address has been

changed and you do not remember the new IP

address, you can still access the web interface and see

your current configuration. The default value is not

saved in the configuration, but is only valid until next

reboot.

With the terminal

running, press and hold

the Reset button for 30

seconds, until the Power

indicator on the terminal

is flashing orange.

The terminal restores factory settings and reboots the

system.

While the terminal is

booting, press and hold

the Reset button.

For service use only!

The bootloader initiates software upload.
Refer to the installation manual for details.

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands